Culligan® Good Water Machine® Drinking Water System Owners

Culligan

Good Water

Machine

Drinking

Water

System

Owners

Guide

01018588

NOTICE Do not use with water that is microbiologically unsafe or of unknown

quality without adequate disinfection before or after the system.

For installations in Massachusetts, Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult

your licensed plumber for installation of this system. The use of piercing valves is not permitted in Massa-

chusetts.

Check with your public works department for applicable local plumbing and sanitation codes. Follow your

local codes if they differ from the standards used in this manual.

Operational, maintenance and replacement requirements are essential for this product to perform prop-

erly. The Good Water Machine® contains replaceable particulate and activated carbon filters. It also

includes a replaceable reverse osmosis membrane filter which is critical for the effective reduction of Total

Dissolved Solids. The filtered water should be tested periodically to verify that the system is performing

properly.

Culligan International Company

9399 W. Higgins Road, Suite 1100

Rosemont, Illinois USA 60018

847/430-2800

www.culligan.com

Products manufactured and marketed by Culligan International Company (Culligan) and its affiliates are

protected by patents issued or pending in the United States and other countries. Culligan reserves the right

to change the specifications referred to in this literature at any time, without prior notice. Culligan, Good

Water Machine, Aqua Cleer, Culligan Man and www.culligan.com are trademarks of Culligan Interna-

tional Company or its affiliates.

01018588

System Specifications .............................................................................................................................................................................. 1

Introduction ................................................................................................................................................................................................ 2

Installation ................................................................................................................................................................................................... 5

Servicing Your System ............................................................................................................................................................................. 7

Parts List ...................................................................................................................................................................................................... 11

Culligan

Good Water Machine

Service Log .................................................................................................................................12

Performance Data Sheet ....................................................................................................................................................................... 13

Culligan Lifetime Limited Warranty .................................................................................................................................................. 17

Table of

Contents

iii

01018588

About this

Manual

This manual:

• familiarizes the operator with the equipment

• explains installation and setup procedures

• gives specifications and troubleshooting information

• provides servicing information.

Read this Manual First

Before you operate the Culligan Good Water Machine

Drinking Water System, read this manual to

become familiar with the device and its capabilities.

Safe Practices

Throughout this manual there are paragraphs set off by special headings.

Notice (or Note) is used to emphasize installation, operation or maintenance information which is import-

ant, but does not present any hazard. For example,

NOTICE The nipple must extend no more than 1 inch above the cover plate.

Caution is used when failure to follow directions could result in damage to equipment or property.

CAUTION! Disassembly while under water pressure can result in flooding.

Warning is used to indicate a hazard which could cause injury or death if ignored.

WARNING! Electrical shock hazard! Unplug the unit before removing the

timer mechanism or cover plates!

The CAUTION and WARNING paragraphs are not meant to cover all possible conditions and situations

that may occur. Understand that common sense, caution, and careful attention are conditions which

cannot be built into the equipment. These MUST be supplied by the personnel installing, operating, or

maintaining the system.

Be sure to check and follow the applicable plumbing codes and ordinances when installing this equip-

ment. Local codes may prohibit the discharge of sanitizing or descaling solutions to drain.

Use protective clothing and proper face or eye protection equipment when handling chemicals or tools.

NOTE The Culligan Good Water Machine

Drinking Water System is not intended for

use with water that is microbiologically unsafe or of unknown quality without

adequate disinfection either before or after the system.

NOTE Check with your public works department for applicable local plumbing and

sanitation codes. Follow local codes if they differ from the standards used in

this manual. To ensure proper and efficient operation of the Culligan Good

Water Machine

Drinking Water System to your full satisfaction, carefully

follow the instructions in this manual.

01018588

Dimensions Filter Assembly 7.5”W x 3”D x 16.5”H

Storage Tank Std 9” Diameter x 14”H

Medium 11” Diameter x 14”H

Large 15.5” Diameter x 24”H

Storage Capacity Standard Tank 2 gallons

Medium Tank 3 gallons

Large Tank 9 gallons

System Flow Sequence Particle Filter, Activated Carbon Filter,Reverse Osmosis Membrane Filter,

Storage Tank, Polishing Filter, Dispensing Faucet

Particle Filter 5 Micron Spun Polypropylene

Activated Carbon Filter Solid Carbon Block

Reverse Osmosis Membrane

Filter

Culligan Aqua-Cleer

Thin Film Composite

Polishing Filter Cullar G Activated Carbon

Dispensing Faucet Culligan Aqua-Cleer Faucet Rotary Operation, Stainless Steel and Resin

Flow Passages, with Built-in Siphon Break

Colors Polished Chrome or White

Model 2 Gallon 3 Gallon 9 Gallon

System DPR* to Storage Tank 14.5 (54.88L) 14.5 (54.88L) 14.5 (54.88L)

Efficiency Rating

17.9% 17.9% 17.9%

Recovery Rating

30.8% 30.8% 30.8%

* DPR - Daily Production Rate

Product Production Rate without storage tank to atmosphere

- AC-30 Models......................30 gpd (114 L/day)

Ratio of Product to Flush Flow

Soft Water Applications...........2:3

Hard Water Applications.........1:3 - 1:5

Rating at 50 psi, 77°F, 500 mg/L TDS Influent, Without Storage Tank to atmosphere. This is a factory

specification for membrane production. Actual production rate and TDS rejection will depend on tempera-

ture, water pressure, TDS level, membrane variation and usage pattern.

May vary with pressure. See Technical Manual (P/N 01018587) for all hard water applications and

applications where TDS exceeds 1000 mg/L (ppm).

Efficiency rating means the percentage of the influent water to the system that is available to the user as

reverse osmosis treated water under operating conditions that approximate typical daily usage.

Recovery rating means the percentage of the influent water to the membrane portion of the system that is

available to the user as reverse osmosis treated water when the system is operated without a storage tank

or when the storage tank is bypassed.

System

Specifications

01018588

Thank you for choosing a Culligan Good Water Machine® drinking water system. Your new system is

designed to bring you years of deliciously crystal-clear Culligan® water. With its special faucet installed

on your sink, it’s like getting bottled water straight from your kitchen tap.

With three separate filter technologies and its unique space-saving design, the Good Water Machine is

the most advanced drinking water system available today from Culligan.

About Your System

The reverse osmosis method of water treatment has long been regarded as one of the most efficient and

effective ways to reduce impurities. It’s the technology we’ve used to build your new Culligan Good Water

Machine. In addition, we’ve incorporated activated carbon and fine particle filtration to bring you one of

the most effective systems available today.

Good Water Machine System Components

Refer to Figure 1 on page 6.

Particle Filter

The particle filter reduces dirt, sand, rust, and other microscopic particles 15 times smaller than a grain of

sand.

Activated Carbon Filter

The activated carbon filter reduces elements that cause water to taste and smell unpleasant, including the

taste and odor of chlorine, if present in your untreated water supply.

Reverse Osmosis Membrane Filter

The reverse osmosis (RO) membrane filter reduces dissolved substances, including radium, lead, and many

others. These substances may not be in your water. See Performance Data Sheet for list of substances and

removal percentages.

Manifold Assembly

The manifold serves as the functional hub of the system, directing and regulating the flow through each of

the system’s components. It makes the Good Water Machine extremely space efficient and simplifies filter

changes.

Storage Tank

The storage tank holds up to 2 gallons of triple-filtered Culligan water under pressure for rapid delivery.

Optional three and nine-gallon tanks are available.

Polishing Filter

The Good Water Machine includes a second activated carbon filter as added assurance that your water

will be crystal clear.

Faucet

The special drinking water faucet mounts conveniently on your kitchen sink. A simple twist of the handle is

all it takes to enjoy refreshing Culligan drinking water.

Introduction

01018588

Certified Performance

The Culligan Good Water Machine Model AC-30, AC-30M, AC-30L, AC-30 Plus, AC-

30M Plus and AC-30L Plus Drinking Water Systems have been tested and certified by

WQA to NSF/ANSI 372, and CSA B483.1, and NSF/ANSI Standard 58 for the ef-

fective reduction of TDS, Barium, Cadmium, Hexavalent and Trivalent Chromium, Lead,

Radium 226/228, Copper and Selenium as verified and substantiated by test data.

Average removal percentages are as follows:

AC-30 (M,L) & AC-30 Plus (M,L)

Barium................95.2%

Cadmium............99.2%

Chromium III........98.6%

Chromium VI........75.1%

Copper................85.3%

Lead....................98.4%

Radium 226/228 ............95.2%

Selenium .........................91.9%

TDS/Sodium Chloride.......80% (2 Gallon Tank)

.......80% (3 Gallon Tank)

.......80% (9 Gallon Tank)

The substances removed by this system are not necessarily in your untreated water. See Performance

Data Sheet starting on page 13 for exact percentages of contaminant removal.

01018588

How To Use Your System

With the Good Water Machine, you’ll get a continuous supply of clear, refreshing water for drinking and

cooking. But Culligan improves a lot more than just water. Crystal clear Culligan water is ideal for:

• coffee • recipes • pasta

• tea • baby formula • ice cubes

• soup • house plants • steam irons

• juice • pets • drink mixes

• everything you make with water

Performance Check

This system contains a replaceable treatment component, critical for the effective reduction of Total Dis-

solved Solids, and that product water shall be tested periodically to verify that the system is performing

properly.

“This reverse osmosis treatment system contains a replaceable component critical to the efficiency of the

system. Replacement of the reverse osmosis component should be with one of identical specification, as

defined by the manufacturer, to assure the same efficiency and contaminant reduction performance.”

To check the performance of your Good Water Machine, it is necessary to measure the total dissolved

solids (TDS) level of the filtered water. This simple test can be done quickly by your dealer.

The Good Water Sentry™ Water Quality Monitor is another way to keep track of your system’s perfor-

mance. This optional accessory checks your drinking water each time you

use the special faucet, and signals when the membrane filter may need to be replaced.

AC-30 Plus, AC-30L Plus, and AC-30M Plus come with the Good Sentry Water Quality Monitor.

The Good Water Machine® Models are supplied with a nitrate test kit. Product water must be tested

frequently according to the instructions provided with the kit.

If the water quality of your system seems to have declined, drain the storage tank and allow the system to

refill. If the problem persists, call your Culligan Man™ for service.

Suggested Installation Equipment

Sink Cutting Tools

• Porcelain Cutter Kit, 1-1/4 inch diameter,

P/N 00591625

• Greenlee Hole Punch, 1-1/4 inch diameter

• Plumbers Putty

• Heavy Duty Drill with speed control to

400 rpm

Tools

• Screwdriver, blade and Phillips (#1)

• 1/8 inch diameter pilot drill for #10 screws

• Center Punch

• Razor Blade Knife

• Faucet Installation Tool, P/N 00403375

• Aqua-Cleer H Series or “System” series

filter housing

01018588

Installation

This Owner’s Guide provides visual assembly reference only. Since specialized skills are required in the

assembly of the drinking water system, we recommend that you contact your local independently operated

Culligan dealer to complete this installation.

Please refer to the Aqua-Cleer/Good Water Machine Drinking Water Systems Technical Manual (P/N

01018587) for installation guidelines on the following topics:

• Faucet Installation • Flushing Procedure for Pre-Filters

• Storage Tank Settings • Post Installation Performance Measurements

Application Guidelines

The Good Water Machine is designed for use on potable water supplies meeting the guidelines outlined

in Table 1. The system should be installed on your home’s cold water line. The flushing stream should

discharge through an approved siphon break as illustrated in Figure 1 on page 6. Installation of this

system must comply with state and local laws and regulations.

The Good Water Machine may also be used to provide crystal-clear Culligan water to other drinking wa-

ter using appliances such as an icemaker or refrigerator. Installing the unit to supply filtered water to other

appliances may be complicated and require additional components for proper use. We again recommend

that you contact your local independently operated Culligan dealer to complete this type of installation.

Use of the Good Water Machine with these and other appliances must follow the guidelines set forth in

the Aqua-Cleer/Good Water Machine Drinking Water Systems Technical Manual (P/N 01018587).

Installations that do not follow these guidelines run the risk of working improperly or even causing damage

to the appliances.

Table 1. Influent Water Characteristic

Pressure 40 - 120 psi (280 - 827 kPa)

Temperature 33 - 100°F (1 - 38°C)

Total Dissolved Solids (TDS)

0 - 2500 ppm ( 0 - 2500 mg/L)

pH 5 - 10

Chlorine

0 - 3 ppm ( 0 - 3 mg/L)

Chloramine 0 - 3 ppm ( 0 - 3 mg/L)

Turbidity 0 - 10 NTU

Hardness

0 - 10 gpg

Iron 0 - 1 ppm (0 - 1 mg/L)

Bacterial Quality Potable

See the Technical Manual for all applications where TDS exceeds 1000 ppm (1000 mg/L). A booster

pump is strongly recommended.

The reverse osmosis membrane filter used in this system may be damaged by chlorine. This system

includes activated carbon which protects this element by reducing chlorine. Influent chlorine should not

exceed 3 mg/L.

A softener is strongly recommended for water over 10 gpg.

01018588

The exact placement of the components will vary by installation. Although shown beneath a sink, it may

be installed in a basement, crawl space, or in an adjacent cabinet. Regardless of where the system is

installed, the flow sequence described by (Figure 1) must be observed.

The Aqua-Cleer

/Good Water Machine

drinking water system is designed to be mounted near a sink

for easy access to cold water and drain lines. Lengths of 1/4-inch and 3/8-inch OD plastic tubing will

be required to make this installation. A length of Culligan

drain tubing is required to install the air gap

siphon break.

Evaluate the installation site to determine the easiest path for the plumbing to follow. Take care to make

the installation as neat as possible.

Aqua-Cleer

Faucet

Monitor

Sensor

Monitor

Drain

Cold Water

Supply

Post

Filter

1/4" Tubing

to Faucet

Air Gap

Feed Line

1/4" Tubing

AC-30

Manifold

3/8" Tubing to Faucet Product Port

Ball Valve

Tank

3/8" Tubing

to Faucet

Product

Port

Tubing From Faucet

Air Gap - 3/8” Tubing

Figure 1.

NOTICE Install the drain line so that it runs downward with no loops or low spots.

Otherwise the unit will overflow at the air gap siphon break built into the

faucet, or make irritating gurgling sounds. The concentrate line that leads

to the faucet should be installed in a straight vertical path to avoid mak-

ing a gurgling noise.

01018588

Servicing Your

System

Service Schedule

When properly maintained, your Good Water Machine will give you years of dependable service. Use

the following as a guide to get the most out of your system. Service frequency may vary depending on

your local water conditions. High sediment, chlorine, turbidity, or hardness levels may require more fre-

quent service. Refer to Figure 3 & Figure 4.

At Least Once Per Year

Replace:

• Particle Filter (1)

• Activated Carbon Filter (2)

• Polishing Filter (4)

Check:

• RO Membrane Filter (3)

- TDS Reduction Performance

- Flow Rates

• Capillary Assembly

Sanitize the System.

Use the convenient chart inside the back cover of this booklet to keep track of your system’s maintenance.

Filter Replacement

Culligan recommends that you have your Good Water Machine serviced by your local Culligan Man. You

can rely on his or her experience and expertise to keep your system in top operating condition.

If you wish to service your system, the filters are available from your Culligan dealer. For replacement

components, or to measure the Total Dissolved Solid (TDS) Reduction Performance please contact your

local Culligan Dealer or 1-800-CULLIGAN (1-800-285-5442) for the dealer near you. See the “Parts List”

on page 11 for replacement numbers.

Cartridge Conditioning

The activated carbon, reverse osmosis, polishing filter, and particle filter cartridges must be conditioned

as follows prior to installation into the Good Water Machine. Your Culligan Man can do these important

procedures at the time of purchase.

Activated Carbon Cartridge —10-minute flush to remove carbon dust

RO Membrane Filter—Minimum 24-hour flush to remove preservative solution

Polishing Filter—2-gallon flush to remove carbon dust

Particle Filter—10-minute flush

01018588

Tubing Connectors

The Good Water Machine features easy-to-use push-in tubing connec-

tors (Figure 2) on the manifold assembly and the polishing filter.

To disconnect the connector, hold the collar against the fitting body

and pull the tube from the fitting.

To assemble lubricate the tubing end with water and push the tubing

into the connector until it bottoms out. Be sure the tubing is smooth and

free of abrasions, otherwise a leak may result.

Figure 3.

Filter Replacement and Sanitizing Procedure

Use the following procedure and the reference in Figure 3 when servicing the Good Water Machine.

NOTICE Cleanliness is essential in the filter replacement procedure. Be sure to

wash your hands thoroughly before handling filters. The use of protective

gloves is strongly recommended.

Materials:

• Pre-flushed activated carbon cartridge and polishing filter cartridge

• Particle filter

• Household (5.25%) bleach—hydrogen peroxide is not recommended

• Clean 1-gallon plastic container with cap

• 100-ml graduated cylinder

• Plastic pan to hold manifold assembly

• Tubing connector, 3/8” tube x 3/8” tube

• Flat-blade and #2 Phillips screwdrivers

• Paper towels

• Disposable plastic gloves (like those used in the food service industry)

Figure 2.

Flow

Fittings

Figure 4.

01018588

Preparation

1. Locate the system’s supply valve and turn off the system’s water supply.

2. Using the graduated cylinder, add 5 ml (about 1 teaspoon) of bleach to the 1-gallon container.

Open the dispenser faucet and fill with one gallon of product water. If there is not enough RO

water, fill the container the rest of the way with soft water. Cap the container and shake to mix.

NOTICE If any RO water remains after filling the container, you may want to fill a

pitcher with the drinking water as it will take several hours for the system

to refill after servicing. In any case, leave the faucet open until the storage

tank is empty and then, close the faucet.

3. Remove the polishing filter (Figure 4) and discard. Connect the tubing ends together with the

tubing connector.

4. Lift the filter assembly from the mounting bracket and place it in the plastic pan to catch any

dripping water.

5. Using the flat-blade screwdriver, pull the u-clips from all three housings. Insert the u-clip into the

two square holes at the bottom rear of the manifold and push up to release the filter housings.

Remove the housings with a downward twisting pull.

6. Remove the particle filter cartridge and the activated carbon cartridge and discard. If the RO

membrane filter will be reused, clean the outside with a wet paper towel and place the mem-

brane filter in a clean, unused plastic bag.

7. Wet some paper towels with the diluted bleach solution. Clean the inside of the housings and

the underside of the manifold with the paper towels.

Sanitizing the Storage Tank and Faucet

1. Add 15 ml (about one tablespoon) of bleach to the particle filter housing (#1, Figure 3).

Replace all three housings on the manifold and insert the u-clips.

NOTICE The weight of the storage tank will increase by 8 to 16 pounds. Turn off

the water supply valve.

2. Turn on the supply valve and fill the storage tank with 1 to 2 gallons of water.

3. Wait ten minutes before opening the faucet and draining the storage tank. Do not rinse any

remaining solution from the tank.

NOTICE During this time, proceed to the “Sanitizing the Manifold Assembly” on

page 10.

Wait to do step 4 until indicated.

4. Remove the temporary tubing connector and replace it with a new polishing filter. Make sure

the flow arrow on the polishing filter points to the faucet (Figure 4).

01018588

Sanitizing the Manifold Assembly

1. Using the flat-blade screwdriver, pull the u-clips from all three housings. Insert the u-clip into the

two square holes at the bottom rear of the manifold and push up to release the filter housings.

Remove the housings with a downward twisting pull. Discard any solution remaining in the hous-

ings.

2. Open the particle filter cartridge bag half way, being careful not to touch the filter element.

Lubricate the particle filter cartridge o-rings with water and insert the cartridge into position #1

in the manifold.

3. Fill housing #1 about 2/3 full of the diluted bleach solution from the 1-gallon container.

Assemble the housing to the manifold and replace the u-clip.

4. Repeat steps 2 and 3 for housing #2 (activated carbon cartridge) and housing #3 (RO mem-

brane filter).

NOTICE For RO membrane filters that have a single open-end, pour diluted bleach

solution into the center tube.

CAUTION! The solution should remain in contact with the RO membrane

filter for at least five (5) but no longer than ten (10) minutes.

Longer contact time will shorten the life of the membrane.

NOTICE While waiting for the filters to be sanitized, complete step 4 of the “Sani-

tizing the Storage Tank and Faucet” on page 9. Then complete step 5

below.

5. Using the #2 Phillips screwdriver, loosen the capillary assembly retaining screws, then twist and

remove the assembly. Inspect the tubing for plugging and kinks and replace the tubing as need-

ed. Reinstall the capillary assembly, but leave the screws 1/4 turn loose.

6. In this step, you will need to observe water flowing to the drain. If the drain flow is not visible

with the current tubing connections, install a temporary drain tube in the waste port of the man-

ifold. Turn on the supply valve. When water is seen flowing to the drain, carefully loosen the

capillary tube assembly retaining screws until the flow to the drain increases.

NOTICE When the assembly is about 3/16” out of the manifold, the o-ring seal for

the capillary tube is bypassed, but there should be no external leaks.

7. Rinse the manifold assembly for five minutes or until no chlorine is detected in the water passing

to the drain. Tighten the capillary assembly retaining screws.

8. Check the performance of the system according to the procedure outlined in the “Performance

Check” on page 4. Replace the RO membrane if necessary.

9. Instruct the customer to discard the first glassful of water from the system to flush out any resid-

ual chlorine that might remain in the polishing filter tubing and faucet. The polishing filter will

remove any chlorine remaining in the storage tank.

10. Record your service on the chart on page 12.

01018588

Parts List

Item Description Part Number

1 Mounting Bracket 01004081

2 Faucet - Chrome 01018401

Faucet - White 01018402

Faucet - Chrome w/ Light 01018468

Faucet - White w/ Light 01018469

3 Polishing Filter GAC, 10 Pack P1004291

Polishing Filter GAC, 50 Pack 01007468

Polishing Filter Block, 10 Pack 01014612

Polishing Filter Block, 50 Pack 01014613

4 Plastic Ball Valve 01004550

5 Storage Tank - Std. 01005095

Storage Tank - Medium 01004776

Storage Tank - Large 01004765

6 Screw, #10.9 x .625” Pan Head Phil., 25 Pack P0401016

7 Sediment Filter, 10 Pack 01000120

Sediment Filter, 50 Pack 00402809

8 Capillary Assembly 01009025

9 Reverse Osmosis Membrane Element AC-30 Non-Nitrate, 25 Pack 01007408

Reverse Osmosis Membrane Element AC-30 Non-Nitrate, 10 Pack 01007409

10 Drain Adapter Assembly, 10 Pack P1004292

11 Activated Carbon Filter, 12 Pack P1012580

Activated Carbon Filter, 50 Pack 01012600

Service Kit (contains a Sediment Filter, an Activated Carbon Filter, a RO Membrane, a Polishing Filter

GAC and a Capillary Assembly)

01007411

* Service Kit (contains a Sediment Filter, an Activated Carbon Filter and a Polishing Filter Block) 01021561

* Icemaker Tee -3/8 x 3/8 x 1/4, 10 Pack P1004728

* Tubing, Blue - 1/4” O.D. 00402184

* Tubing, Blue - 3/8” O.D. 01000287

* Good Water Sentry Monitor 01019619

* Aqua-Cleer Booster Pump 01009334

* Not Illustrated

01018588

Culligan

Good Water

Machine

Service Log

Model: Serial No.:

Date Installed: For Service Call Culligan At: ( )

Date

Serviced

Filter(s) Changed

Sanitized

Particulate

Filter

Activated

Carbon Filter

RO Membrane

Filter

Polishing

Filter

01018588

Performance

Data Sheet

Important Notice: Read this Performance Data Sheet and compare the capabilities of the unit with your

actual water treatment needs. Culligan recommends that you have your water supply tested to determine

these needs before purchasing a water treatment unit.

Culligan knows the more informed you are about your water treatment systems, the more confident you

will be about its performance. It’s because of this and more than seventy years of commitment to customer

satisfaction that Culligan is providing this Performance Data Sheet to its customers.

Manufacturer: Culligan International Company,

9399 W. Higgins Rd, Suite 1100, Rosemont, IL 60018 USA

(847) 430-2800

www.culligan.com

Product: Culligan Good Water Machine Reverse Osmosis Drinking Water System

MODELS: • AC-30 • AC-30 Plus

• AC-30M • AC-30M Plus

• AC-30L • AC-30L Plus

Use Guidelines

• Working Pressure: 40-120 psig (280-827 kPa)

• Do not allow exposure to temperatures below 33°F (1°C)

• Maximum operating temperature: 100°F (38°C)

• This system must be installed according to local plumbing codes on the cold water line.

• This system requires regular replacement of all filters to maintain proper operation. Depending

on usage and influent water quality, the carbon and particulate filters should be changed at least

annually and the reverse osmosis membrane should be replaced every 3-5 years. Varying chlorine,

sediment or TDS levels may affect replacement frequency.

MSRP

• Particulate Prefilter Element.....................00-4015-38...............................................30.00

• Activated Carbon Prefilter Element..........01-0125-80................................................40.00

• Activated Carbon Postfilter Element.........01-0042-91................................................20.00

• RO membrane......................................01-0074-02................................................95.00

• If water production decreases or a noticeable taste change occurs, contact your local Culligan

Dealer. A Culligan professional can determine if your drinking water system requires servicing.

Optional water quality monitors are also available to monitor the performance of the reverse osmo-

sis membrane.

• Caution! Do not use with water that is microbiologically unsafe or of unknown quality without

adequate disinfection before or after the system.

• The Good Water Sentry Water Quality Monitor is another way to keep track of your systems per-

formance. This optional accessory checks your drinking water each time you use the special faucet,

and signals when the membrane filter may need to be replaced.

01018588

These systems have been tested and certified by WQA according to NSF/ANSI 372, and CSA

B483.1, and NSF/ANSI Standard 58 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a

concentration less than or equal to the permissible limit for water leaving the system, as

specified in NSF/ANSI 58.

Substance Removal

Substance Influent

Challenge

Concentration

(mg/L)

Max. Permissible

Product Water

Concentration

(mg/L)

Minimum

Percent

Removal

Average

Percent

Removal

Barium 10.0 +/- 10% 2.0 89.10% 95.20%

Cadmium 0.03 +/- 10% 0.005 92.20% 99.20%

Hexavalent Chromium 0.30 +/- 10% 0.1

67.90% 75.10%

Trivalent Chromium 0.30 +/- 10% 0.1 94.70% 98.60%

Copper 3.00 +/- 10% 1.3 85.30% 85.30%

Lead 0.15 +/- 10% 0.010 93.50% 98.40%

Radium 226/228

25 pCi/L +/- 10% 5 pCi/L 89.10% 95.20%

Selenium 0.10 +-/10% 0.05 79.90% 91.90%

While testing was performed under standard laboratory conditions, actual performance may vary de-

pending on water pressures, temperatures, and other substances which may be found in your water.

Based upon testing methods using Barium as a surrogate. All concentrations in pCi/L: Pico curies per

liter.

01018588

Output (Total Dissolved Solids (TDS) Reduction and Output Production)

Tank Size 2 Gallon 3 Gallon 9 Gallon

Product system daily prod. rate to pressur-

ized storage tank

14.5 gpd (54.8 L) 14.5 gpd (54.8 L) 14.5 gpd (54.8 L)

Prod. rate w/o storage tank to atmosphere 30 gpd 30 gpd 30 gpd

Efficiency rating

17.9% 17.9% 17.9%

Recovery rating

30.8% 30.8% 30.8%

Influent challenge concentration (mg/L) 750 +/- 40 mg/L 750 +/- 40 mg/L 750 +/- 40 mg/L

Max. permissible product water concentra-

tion (mg/L)

187 187 187

Minimum percent removal 76.6% 76.6% 76.6%

Average percent removal 81.6% 81.6% 81.6%

This is a factory specification for membrane production. Actual production rate and TDS rejection will

depend on temperature, water pressure, TDS level, membrane variation and usage pattern.

Efficiency rating means the percentage of the influent water to the system that is available to the user as

reverse osmosis treated water under operating conditions that approximate typical daily usage.

Recovery rating means the percentage of the influent water to the membrane portion of the system that is

available to the user as reverse osmosis treated water when the system is operated without a storage tank

or when the storage tank is bypassed.

Testing Conditions (Complete Systems)

Temperature: 77° F ± 2° F pH: 7.5 ± 0.5

Pressure: 50 psi Turbidity: < 1 NTU

This system has been tested and shown to operate at its calculated recovery rating under standard test conditions.

Dimensions

Filter Assembly 7.5” W x 3” D x 16.5” H (20 cm W x 8 cm D x 42 cm H)

Storage Tank Standard 9” Diameter x 15” H (23 cm Diameter x 38 cm H)

Medium 11” Diameter x 15” H (28 cm Diameter x 38 cm H)

Large 15.5” Diameter x 22” H (40 cm Diameter x 56 cm H)

The Good Water Machine models listed above have been tested and certified by WQA ac-

cording to NSF/ANSI 372, and CSA B483.1, and NSF/ANSI Standard 58 for the effective reduc-

tion of TDS, Barium, Cadmium, Hexavalent and Trivalent Chromium, Lead, Radium 226/228,

Copper and Selenium as verified and substantiated by test data. The concentration of the

indicated substances in water entering the system was reduced to a concentration less than

or equal to the permissible limit for water leaving the system as specified in NSF/ANSI 58.

Refer to your Installation and Operating Instructions and printed limited Warranties for more specific product

information. To avoid contamination from improper handling and installation, your system should only be

installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The sub-

stances reduced by this system are not necessarily in your water.

NOTE To maintain product certification and ensure uniform performance, the product is retested on a

consistent basis.

NOTE The system must be installed and maintained according to the manufacturer’s recommendations,

including replacement of filter cartridges. Please see the product installation manual (P/N

01018588) for more details.

01018588

Table 2. Influent Water Characteristic

Pressure 40 - 120 psi (280 - 827 kPa)

Temperature 33 - 100°F (1 - 38°C)

Total Dissolved Solids (TDS)

0 - 2500 ppm ( 0 - 2500 mg/L)

pH 5 - 10

Chlorine

0 - 3 ppm ( 0 - 3 mg/L)

Chloramine 0 - 3 ppm ( 0 - 3 mg/L)

Turbidity 0 - 10 NTU

Hardness

0 - 10 gpg

Iron 0 - 1 ppm (0 - 1 mg/L)

Bacterial Quality Potable

See the Technical Manual (P/N 01018587) for all applications where TDS exceeds 1000 ppm (1000

mg/L). A booster pump is strongly recommended.

The reverse osmosis membrane filter used in this system may be damaged by chlorine. This system

includes activated carbon which protects this element by reducing chlorine. Influent chlorine should not

exceed 3 mg/L.

A softener is strongly recommended for water over 10 gpg.

Application Guidelines

The Good Water Machine is designed for use on potable water supplies meeting the guidelines outlined

in Table 2. The system should be installed on your home’s cold water line. The flushing stream should

discharge through an approved siphon break as illustrated in Figure 1 on page 6. Installation of this

system must comply with state and local laws and regulations.

01018588

Culligan Good Water Machine

AC-30 Model Series

You have just purchased one of the finest drinking water systems made. As an expression of our con-

fidence in Culligan products, your drinking water system is warranted to the original end-user, when

installed in accordance with Culligan International Company specifications, against defects in material

and workmanship from the date of original installation, as follows:

For the LIFETIME of the

original end-user

The entire reverse osmosis water conditioning unit, EXCLUDING THE

EXPENDABLE FILTER CARTRIDGES AND REVERSE OSMOSIS

MEMBRANE FILTER USED IN THE UNIT.

For a period of ONE YEAR The Culligan brand reverse osmosis membrane filter.

If a part described above is found defective within the specified period, you should notify your inde-

pendently operated Culligan dealer and arrange a time during normal business hours for the dealer to

inspect the drinking water system on your premises. Any part found defective within the terms of this war-

ranty will be repaired or replaced by the dealer. You pay only freight from our factory and local dealer

charges.

Damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, alteration,

installation or operation contrary to our printed instructions, or by the use of accessories or components

which do not meet Culligan specifications, is not covered by this warranty.

Our product performance specifications are furnished with each drinking water system. TO THE EX-

TENT PERMITTED BY LAW, CULLIGAN DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING, WITHOUT

LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE; TO THE

EXTENT REQUIRED BY LAW, ANY SUCH IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE

ONE-YEAR PERIOD SPECIFIED ABOVE FOR THE PARTS DESCRIBED IN THIS LIMITED WARRANTY. As

manufacturer, we do not know the characteristics of your water supply or the purpose for which you are

purchasing a drinking water system. Please understand that the quality of water supplies may vary season-

ally or over a period of time, and that your water usage rate may vary as well. Water characteristics can

also change considerably if your drinking water system is moved to a new location. For these reasons, we

assume no liability for the determination of the proper equipment necessary to meet your requirements,

and we do not authorize others to assume such obligations for us. Further, we assume no liability and

extend no warranties, express or implied, for the use of this product on a non-potable water source. OUR

OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED TO THE REPAIR OR REPLACEMENT OF THE

FAILED PARTS OF THE DRINKING WATER SYSTEM, AND WE ASSUME NO LIABILITY WHATSOEVER

FOR DIRECT, INCIDENTAL, CONSEQUENTIAL, SPECIAL, GENERAL, OR OTHER DAMAGES, WHETHER

FROM CORROSION OR OTHER CAUSES.

CONSUMERS:

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may

not apply to you. Similarly, some states do not allow the exclusion of incidental or consequential damag-

es, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights,

and you may also have other rights which vary from state to state. Consult your telephone directory for

your local independently-operated Culligan dealer, or write Culligan International Company, for warranty

and service information.

Culligan International Company

9399 W. Higgins Road, Suite 1100

Rosemont, Illinois 60018

www.culligan.com

Culligan Lifetime

Limited Warranty

01018588

Notes