2985 Narrow Stile Lever Handle
*with Passage Function
Installation Instructions
Connued on Reverse Side
IMPORTANT INFORMATION ABOUT YOUR DIGITAL 2985
1. The Lockey 2985 is designed for narrow sle prep doors or
for configuraons with exisng narrow sle hardware with
1 1/8” prep. The 2985 can also be installed on new morse
prep doors, 2”x2” gates or chainlink gates.
2. In order to work with Lockey keyless locks, the
drive/spindle hole is located on the boom of the latch.
The system operates opposite compared to Adams-Rite style
products. The strike may need to be modified.
3. When the door is closed, the system locks automacally.
4. From the inside, unlock using the Lever Handle.
5. From the outside, unlock by pressing ‘C’ (CLEAR), followed
by your User Code.
PASSAGE FUNCTION:
The 2985 is equipped with a PASSAGE FUNCTION,
allowing you to leave the door unlocked.
-To enable the passage funcon:
Press ‘C’ (CLEAR), then ‘Y’ (PASSAGE), then enter User Code.
-To disable the passage funcon:
Press ‘Y’ (PASSAGE), followed by ‘C’ (CLEAR).
-To disable the passage funcon PERMANENTLY:
Remove the ‘Y’ (PASSAGE) tumbler, leaving that slot empty.
IMPORTANT: Always press and hold the ‘C’ Buon when
removing and inserng Tumblers. Refer to ‘How to Change
Code’ instrucons on reverse side.
Step 1: Change User Code/Combinaon (OPTIONAL)
To change user code/combinaon, see instrucons on reverse side.
Step 2: Prep Door for Installaon with Template
Place template (supplied) on door and fold along door’s edge. Check to ensure proper measurements. Drill holes accordingly.
Step 3: Idenfy Door Handing
Right-Hand Doors – From exterior of door, hinges are on right side (Fig. 1).
Le-Hand Doors – From exterior of door, hinges are on le side (Fig. 2).
Install Support Pin (#13) in position ‘A’ or position ‘B’ on the Outside Body
as shown in Fig. 3. For 2985DC, install extra support pin on the Inside Body.
Now, install/screw Hex Bolts (#15) into the top and boom of the
Outside Body as shown in Fig. 3.
Step 4: Change Latch Handing (if necessary) & Install Latch
IMPORTANT: Do NOT remove Cam from latch when changing handing.
2985 Cam Posion: MUST be on RIGHT side of latch.
2985 Adjustable Head: Pull latch head and twist.
If latch does not pull and twist, proceed with the following steps:
1. Remove screws from both sides of latch casing.
2. Remove cover and interior springs (#1, #2, #3).
3. Remove latch and deadlatch (#4, #8).
4. Carefully remove Latch Pin (#7) and Latch Spring (#6).
5. Replace the Latch Spring (#6) and then move the Deadlatch Acvator (#5)
to the opposite side of the latch, ensuring that it depresses the Latch Spring.
6. Replace the Latch Pin.
7. Replace Latch, Deadlatch, Latching Springs and Cover.
8. Secure Screws on each side of the Latch Casing.
Place the Narrow Sle Deadlatch (#12) in the door prep and secure.
Fig. 3
#8 Latch
#7 Latch Pin
#4 Deadlatch
#2 Small Spring
#1 Cover
#3 Large Spring
#5 Deadlatch Activator
#6 Latch Spring
Cam
No. Part Name 2985
2
1
3
4
5
Outside Body
Inside Body
Lever Handle
Rubber Trim Plate
Strike Plate
Machine Screw M4 x 40mm
Machine Screw M4 x 30mm | 50mm
Extra Code Tumblers (Red)
Extra Non-Code Tumblers (Blue)
Narrow Sle Deadlatch
Support Pin
Tweezers
Hex Bolts
8
9
10
11
12
13
14
15
1
1
2
2
1
2
1 | 1
1
2
1
2
1
2
Spindle
6 1
Allen Wrench
7 1
Faceplate
16
1
11
12
16
15
13
14
13
Updated 3.21.16
/
If latch head is adjustable, pull and twist.
A
B
15
or
6. Replace the cover plate and secure with four (4) Red Screws,
using a #2 screwdriver.
7. TEST CODE before installing/re-installing lock.
3. PRESS & HOLD ‘C’ BUTTON to release tumblers.
IMPORTANT: ‘C’ buon MUST be pressed and held down when
removing and inserng tumblers. Failure to do so will damage
the lock and void the warranty.
WARNING:
Do NOT force tumblers into posion!
4. While holding the ‘C’ BUTTON, remove/add CODE (Red) and
NONCODE (Blue) tumblers to create your desired code.
Ex: 3 Red = 3-Digit Code / 6 Red = 6-Digit Code
5. Aer changing your code, release the ‘C’ BUTTON to secure the
tumblers in place.
INSTALLATION INSTRUCTIONS CONTINUED:
How to Change User Code/Combinaon
SAVE
For more helpful ps and installaon instrucons, visit www.LOCKEYUSA.com
Step 5: Install Lever Handles
Using Allen Wrench (#7), install levers to the inside and outside bodies.
Secure with set screws.
Note: Levers should point towards the door hinges.
The 2985 is equipped with a built-in slip clutch lever handle to prevent damage in
the event of an aempted forced entry.
If lever handle is in posion shown (far right), pull lever back to desired posion.
Step 6: Verify Correct Spindle Length (Fig. 6)
With the Deadlatch installed, hold the Inside Body (#2) and Rubber Trim Plate (#4) to the door.
Place Spindle (#6) through Latch, into the Inside Body, as far as possible.
Spindle should extend from exterior of door 3/8” min. to 5/8” max.
If Spindle is too long, cut it to the correct length using pliers.
*IMPORTANT:
If spindle extends less than 3/8” it may not engage the lock.
If spindle extends more than 5/8”, it will cause the lock to bind.
Step 7: Install the 2985
Place the Rubber Trim Plate (#4) on the backside of the Outside Body (#1).
Place the Outside Body on the door. The Hex Bolts (#15) should extend into the top and bottom holes.
The Support Pin (#13) should extend through the hole in the Latch (#12).
Insert the Spindle (#6) into the Outside Body (#1) ensuring it’s in the proper angled posion.
*IMPORTANT: SPINDLE POSITION/ANGLE
RIGHT-HAND DOORS: From inside, place spindle through Latch, into the Outside Body in the 2:00/8:00 posion (Fig. 7).
LEFT-HAND DOORS: From inside, place spindle through Latch, into the Outside Body in the 10:00/4:00 posion (Fig. 8).
Place the Rubber Trim Plate (#4) and Inside Body (#2) on the inside of the door.
Using a screwdriver, secure the lock to the door with Screws (#9)(Screw length dependent on door thickness).
Test the operaon of the latch by turning the inside lever.
Locate posion where latch strikes door frame and install Strike Plate (#5).
TEST YOUR LOCK: Press ‘C’ buon (clear), followed by your combinaon. Push lever down and lock will open.
TEST PASSAGE: Press ‘C’, followed by ‘Y’, followed by combinaon. Lock should remain unlocked (passage).
TO LOCK: Push ‘Y’, followed by ‘C’. Lock will remain locked.
Aer installing and tesng the lock, secure Faceplate (#16).
NOTE: If lever handle must be pulled up to unlock, change spindle posion/angle (see figures 7 and 8).
If latch scks: First, make sure Support Pin (#13) is in place. Second, verify correct spindle length (see step 6).
1. Using a #2 screwdriver, remove the four (4) Red Screws.
2. Carefully remove cover plate.
WARNING: Springs are aached to plate.
‘C’ = CLEAR (DO NOT REMOVE)
‘Y’ = PASSAGE (‘Y’ Tumbler may be removed to disable PASSAGE FUNCTION)
2:00
8:00
Fig. 7
10:00
4:00
Fig. 8.
Slip Clutch
Fig. 6
= 3/8” to 5/8”
Updated 3.21.16